
The 30-second answer: On an iGen that won’t start, check the oil level on level ground first, then fuel, then the spark plug. If the unit starts and shuts down under a load, or the overload light comes on, unplug everything, restart, and add loads one at a time. Most iGen calls end at one of these checks.
Watch: “Westinghouse Igen4500 Generator Won't Start Overload Light On Then Shuts Down” by Individualized Repair on YouTube. A Westinghouse iGen4500 that would not start, then shut down with the overload light on. The steps match the guide.
The Westinghouse iGen line is a set of inverter generators, sold in several sizes for camping, job sites, and home backup. An inverter makes clean power, which is good for sensitive electronics, and it is usually quieter than a conventional portable. Its control panel shows warning lights, and those lights tell you a lot about what went wrong.
Read the Lights First
Before you change anything, look at the panel. The overload light, a low-oil light, or a shutdown light each points somewhere different. Note which light is on, and check the owner’s manual for what it means on your model. A low-oil shutdown is a protection, not a fault in the electronics, so the fix is usually more oil.
The Unit Won’t Start
- Oil. Many iGen models stop the engine when the oil is low. Check the dipstick on level ground and top up to the full mark.
- Fuel. Old gasoline varnishes the carburetor, and the engine cranks without firing. Drain stale fuel, refill with fresh gas, and check the fuel valve.
- Spark. A fouled or wet spark plug stops the engine. Check the plug, clean or replace it, and confirm the gap matches the manual. The spark plug guide shows how to read the tip.
- Choke and switch. A cold start needs the choke set correctly. Confirm the engine switch is on.
If the unit cranks and fires briefly, then dies, the carburetor is the most likely cause. The starts-then-dies guide explains that pattern.
The Overload Light Comes On
An overload light means the unit has been asked for more power than it can safely give. Turn everything off, then restart the unit with nothing connected. If it runs with no load, add devices one at a time, starting with the smallest. The device that brings on the light is the one to check, or the total is simply above the rating.
Also look at starting loads. A refrigerator or an air conditioner draws a surge when its motor starts, and several motors starting together can trip the overload. The starting watts guide explains the surge.
Shuts Down Under Load
An iGen that runs fine at idle and shuts down under a load may be overloaded, have a bad cord, or have a fuel-delivery problem. Test the load first, as above. If the shutdown happens with a light load, check the cords and the output with a multimeter. The runs but no power guide covers the output side.
Surging or Rough Running
A unit that surges or runs rough usually has a fuel mixture or air problem. Check the air filter and the spark plug first, then the carburetor. The surging guide includes a short load test you can run at home.
CO Sensors and Shutdowns
Many inverter generators have a carbon monoxide sensor that shuts the unit down if it detects a buildup. If your iGen has one, a CO shutdown is a warning. Move the generator outdoors, away from doors and windows, and make sure it has clean air around it. Do not disable the sensor. The CO sensor guide explains the common causes.
Run an iGen outdoors only, at least 20 feet from the house, with the exhaust pointed away from doors and windows. Inverter generators make carbon monoxide just like conventional ones.
Video: A Real No-Start and Overload Repair
The video below works through a Westinghouse iGen4500 that would not start and then shut down with the overload light on. It is a useful companion to the steps above.
When to Call Westinghouse
If the oil, fuel, spark, load, and cords all check out and the unit still will not run, contact Westinghouse support or an authorized service shop. Have the model and serial number ready. The owner’s manual has the light and fault table for your specific model.
Frequently Asked Questions
Why does my iGen shut off when I add a load?
It is most often overload, a short in a device or cord, or a fuel delivery problem. Test the loads one at a time, and check the cords.
Why does my iGen run but make no power at the outlet?
Check the breaker, the cords, and the load. If the outlet still has no output, measure the voltage with a multimeter. An electrical fault needs a technician.
Can I run an iGen in the garage?
No. Inverter generators still make carbon monoxide. Run the unit outdoors only.
