
The 30-second answer: A small engine can use a little oil between changes, and the manual gives the normal range. Check the level on level ground before every run. If the level drops fast, the unit leaves blue smoke, or the oil looks thin and dark soon after a change, the engine is burning oil and needs a diagnosis.
Watch: “Why Your Generator is Burning Oil [8 Reasons]” by Home & Hardware Lab on YouTube. A list of the common causes of oil burning. Use it as a checklist, and run the compression test if the causes above are ruled out.
Many owners worry the first time they top up a generator between oil changes. A small amount of use is normal, but a steady loss of oil is a warning. The difference is in how much you add, how often, and what the exhaust looks like while the unit runs.
Check the Level the Right Way
Stand the generator on level ground. Shut the engine off, and wait a minute so the oil drains back into the crankcase. Pull the dipstick, wipe it, reinsert it fully, and pull it again. Read the level against the marks. Checking a warm engine right after it stops can read low, so use the same method each time.
Write the level and the date in your log. A reading you can compare across weeks is more useful than a single check.
Normal Use Versus Burning Oil
- Normal: the level drops slowly, you add a little oil every few dozen hours, and the exhaust stays clear or a light grey at start-up.
- Burning oil: you add oil after every run, the level drops fast, and the exhaust shows a blue or grey cloud, especially on start-up or under load.
Blue smoke is the classic sign. The exhaust is burning oil that has entered the combustion chamber. The smoke color guide explains what each color usually means.
Causes That Show Up Most Often
- Overfilling. Too much oil can be forced past seals and up the breather, and it looks like burning. Check the level, and drain the extra to the full mark.
- Tilting during transport. Moving the unit on its side lets oil run into the air filter and the cylinder. Keep the unit upright when you move it.
- A dirty or clogged crankcase breather. A blocked breather raises the pressure in the crankcase, which pushes oil out past the seals.
- Worn rings or valve seals. Over many hours, the rings and seals wear and let oil into the combustion chamber. This is an engine problem, and it usually shows up with low compression.
- Wrong oil. Oil that is too thin for the temperature can be drawn past the rings more easily. Use the viscosity the manual specifies for your climate. The oil change guide lists the choices.
Video: Why Generators Burn Oil
The video below goes through the common reasons a generator burns oil. Use it as a checklist. Some of the causes are easy to fix, and others point to a worn engine.
Test Before You Decide
If the causes above are ruled out, a compression test shows whether the rings and valves are holding pressure. Low compression with oil use usually means internal wear. The compression test guide walks through the check, and the repair or replace guide helps you decide what to do next.
Check the oil only with the engine off and cool. Never run a generator with the oil low, since the low-oil shutdown exists to protect the engine. Do not bypass the sensor to keep the unit running.
Keep the Oil Use Down
- Change the oil on the schedule in the manual, and use the grade it calls for.
- Keep the air filter clean, so the engine draws clean air.
- Keep the unit upright during transport and storage.
- Do not overload the unit, since heavy running heats the oil and wears the rings.
Frequently Asked Questions
How much oil should a generator use per hour?
The manual or the engine maker’s data sheet gives the normal range. As a rule, use is low and steady. A steep drop between checks means something is wrong.
Why does my generator smoke only when it starts?
Oil can seep past worn valve guides or rings and collect in the cylinder while the unit sits. The first start burns it off, which causes a puff of blue smoke. A few seconds of smoke is less worrying than smoke that lasts the whole run, but check the level and the compression if it keeps happening.
Can I use a thicker oil to stop the burning?
Not as a fix. Use the viscosity the manual gives for your temperature range. A thicker oil can help a worn engine for a while, but it does not repair the wear, and it can cause starting problems in cold weather.
